Kansas HVAC Pros
A snow-covered two-story house at night during a snowstorm, with one illuminated upstairs window.

HVAC Installation in Wichita, KS

A new system here will heat from October through April and cool from May through September every year. Tell us about the house, and a licensed contractor who covers Sedgwick County will get in touch.

Tell us about the job

It takes about a minute.

Step 1 of 3: Equipment
An unfinished basement featuring concrete block walls, exposed floor joists, and a metal forced-air furnace with ductwork near a central pillar.

Sedgwick County asks a lot of a heating and cooling system

Your furnace has to work from October through April, seven months a year, on winter nights that average 24°F. Then the air conditioner takes over from May through September, working against summer afternoons that average 90°F. Between the two, something is running all twelve months.

Most homes here heat with gas, and a new furnace has to meet the federal efficiency minimum. Sedgwick County has also logged 332 damaging wind events and 11 winter storms over the past ten years, and storms like that knock out power. Almost a fifth of Kansas households went at least 24 hours without it in 2024. A new system is worth planning around that, not just the heat and cold it has to answer to.

7 months
October through April, your system heats
5 months
May through September, it cools
24°F
the average winter night it heats against
90°F
the average summer afternoon it cools against
Isometric cutaway illustration of a single-story house with a dark shingled roof, showing a furnace with a flue pipe and branching ductwork running through interior rooms furnished with a sofa, table and chairs.
Your system heats October through April and cools May through September.

NOAA nClimDiv, 1991–2020 normals

In Kansas, HVAC licensing for homes is left to the counties and cities.

Sedgwick County sets its own rule for who can do this work, since Kansas leaves that decision to counties and cities. There is no state license or state record to check here. Whether a contractor has to be licensed, and what that takes, depends on the county or city rule where the house sits rather than anything set in Topeka.

For a job like this, installing a furnace and an air conditioner or heat pump, the protection comes from the permit process rather than a license. Most cities and counties require a permit from the local building office for this kind of installation, along with an inspection once the work is done. That inspection is what catches a bad gas connection or a system put in wrong, since that is the part of the job that can actually hurt someone.

Source: Kansas Office of Revisor of Statutes

When should I replace my HVAC system?
Replace it when repairs start coming often, when the unit is old enough that parts are getting harder to find, or when a breakdown leaves you without heat or without cooling. A furnace that struggles to keep up on a 24 degree night, or an air conditioner that can't hold the line on a 90 degree afternoon, is telling you something. Age matters too. A system pushing past the range most equipment of its kind is built to last is a system worth replacing before it fails on the worst day of the year rather than after.
Should I replace my furnace and air conditioner at the same time?
If both are old, yes. Homes here need heat or cooling all twelve months, so both sides of the system are working hard year round, and a furnace and air conditioner installed at the same time age together instead of one failing years ahead of the other. If only one is actually failing, a contractor can tell you whether the other has enough life left to wait. Matching a new furnace to an old air conditioner, or the reverse, can also mean the two were never designed to work as a pair.
What happens during an HVAC installation?
A contractor removes the old furnace, air conditioner or heat pump and sets the new equipment in its place, then connects it to your ducts, gas line or electrical circuit and the refrigerant lines running to the outdoor unit. After that comes startup and testing, checking the airflow, the refrigerant charge, and that the thermostat is talking to the system correctly. In most cities and counties this work needs a permit from the local building office, and an inspector checks it once the work is done. That inspection confirms the gas connections and wiring were done right before the contractor leaves.