HVAC Repair in Andover, KS
Homes here need heat from October through April and cooling from May through September. If your system quits, tell us what it's doing and a licensed contractor who covers Butler County will get in touch.
Tell us about the job
It takes about a minute.
Andover runs its system almost year round
Furnaces in Andover work from October through April, and on nights that average 24°F they cycle on and off for hours at a stretch. Each start puts load on the igniter and the parts that get the burner going. When one of those parts wears out, the furnace stops lighting and the house goes cold.
Come May the same system switches over and runs afternoons that average 89°F clear through September. That's 12 months of use with barely a break between seasons for either side to rest. Butler County has also seen 190 damaging wind events and 8 winter storms over the past ten years, and statewide almost one in five households lost power for a day or more in 2024. A furnace or air conditioner that loses power and doesn't restart right can leave a home with no heat or no cooling until someone looks at it.
- 7 months
- October through April, your system heats
- 5 months
- May through September, it cools
- 24°F
- the average winter night it heats against
- 89°F
- the average summer afternoon it cools against

NOAA nClimDiv, 1991–2020 normals
A new furnace and air conditioner would cut about $150 a year off heating and cooling for a typical Butler County home.
Estimates for a typical Butler County home, compared with an older unit built to the previous federal minimum, from EIA household energy data, Kansas fuel prices and NOAA climate normals. Your home will differ.
Repair makes sense when one part has failed.
Replacement makes sense when the furnace's heat exchanger is cracked, the air conditioner's compressor has failed, or repairs keep coming.
In Kansas, HVAC licensing for homes is left to the counties and cities.
Butler County sets its own rule on who can do this work, and Kansas does not step in behind it. Some counties and cities require a license before a contractor can take this kind of job, others leave it open, and the answer changes depending on which side of a line the house sits on. There is no state list of licensed HVAC contractors to check here, because the state does not keep one.
Whatever protection exists on this job comes from Butler County or the local city, not from the state of Kansas. If the repair involves the gas line or venting, that is the part where a bad connection turns dangerous, and any oversight of that work would come from the local building office, not a state licensing board.
Source: Kansas Office of Revisor of Statutes
- Why is my heat not working?
- Most often the thermostat, the igniter, or a safety switch is the cause. If the thermostat screen is blank, check the furnace switch and the breaker before anything else. A furnace that starts and then shuts off within a minute usually has a dirty flame sensor or a clogged filter starving it of air. With nights here averaging 24°F in winter, a furnace that will not stay lit needs attention the same day, since the house can lose heat fast.
- Why is my system running but not cooling the house?
- The blower is moving air, but something between the air and the cold is not working. A dirty filter or blocked return can cut airflow enough that the air coming out never gets cold. Low refrigerant from a leak is another common cause, and that will not fix itself. If the outdoor unit's fan is not spinning, or the coil is coated in ice, that points to the compressor or refrigerant side, and a contractor will need to check it with gauges.
- What can I check before calling for HVAC repair?
- Start with the thermostat. Make sure it is set to heat or cool as needed, the batteries are good, and the temperature is actually set past the room temperature. Then check the filter. A filter clogged with dust chokes airflow and can make a furnace or air conditioner shut down on its own safety switch. Check the breaker box for a tripped breaker, and for a furnace, make sure the switch that looks like a light switch near the unit is on. If all of that checks out and the system still is not heating or cooling, a contractor will need to look at the equipment itself.


