Kansas HVAC Pros
A snow-covered suburban yard and driveway viewed through a frost-edged residential window during an active snowstorm.

Furnace Repair in Salina, KS

Furnaces here run from October through April. If yours quits, tell us what it's doing and a licensed contractor who covers Saline County will get in touch.

Tell us about the job

It takes about a minute.

Step 1 of 3: Equipment
An empty unfinished basement containing a forced-air furnace with overhead ductwork, exposed ceiling joists, and a single hanging light bulb.

Salina asks a lot of a furnace

Your furnace runs from October through April here, seven months of the year. On the cold nights, when the temperature drops to an average of 22°F, it cycles on and off again and again to hold the house steady. Every one of those starts puts wear on the igniter and the parts that get the burner going.

Most homes in Saline County heat with gas, so when the furnace stops, there is no backup warming the house. And when a winter storm knocks the power out, a furnace that depends on electricity to run its blower and controls stops working right along with the lights. Saline County has seen its share of both, wind and winter storms, over the past ten years.

7 months
October through April, your furnace is on duty
22°F
the average winter night it heats against
63%
of homes here heat with gas, so most furnaces here burn gas
13 winter storms
in ten years, the nights a failure hurts most
Isometric line illustration of a cutaway single-story house with a dark shingled roof, showing interior rooms and ductwork connected to a gray furnace unit with a flue pipe.
Your furnace works hardest from November through March.

NOAA nClimDiv, 1991–2020 normals

An unfinished basement interior featuring a large metal furnace unit, exposed ceiling joists, concrete walls, and scattered boxes and cables on the floor.

A new furnace would cut about $130 a year off heating for a typical Saline County home.

  • A new high-efficiency furnace$520 a year
  • An older furnace$650 a year

Estimates for a typical Saline County home, compared with an older unit built to the previous federal minimum, from EIA household energy data, Kansas fuel prices and NOAA climate normals. Your home will differ.

Repair makes sense when one part has failed and the heat exchanger is sound.

Replacement makes sense when the heat exchanger is cracked or the furnace keeps needing parts.

In Kansas, HVAC licensing for homes is left to the counties and cities.

Kansas has no state license for HVAC contractors. Whatever rule applies to a furnace repair in Saline County comes from the county or the city, not the state, so it depends on where the house sits.

A furnace repair comes down to the gas line and the burner, and getting that connection right is the part that matters. In Saline County, where 62.8% of homes heat with gas, there is no state license standing behind that work. Whatever oversight exists on a furnace repair here is whatever the county or city has put in place, not a state credential.

Source: Kansas Office of Revisor of Statutes

Why won't my furnace turn on?
Most often the thermostat isn't calling for heat the way it should, or power isn't reaching the furnace. Check that the thermostat is set below room temperature and has fresh batteries if it uses them. Next check the furnace switch, the one that looks like a light switch near the unit, and the breaker at your panel. If those are fine, the igniter or a safety switch inside the furnace may have failed, and that calls for a contractor to check.
Why is my furnace blowing cold air?
A furnace blows cold air for a few seconds when it first starts, while it warms up, so that part is normal. If it keeps blowing cold, the burners may not be lighting even though the blower is running. This can come from a dirty flame sensor, a failed igniter, or the gas supply being off. With 7 months of heating ahead here, this is worth having a contractor look at soon rather than waiting.
Why won't my furnace pilot light stay lit?
A pilot light that won't stay lit usually means the thermocouple has worn out. That's the small metal rod that sits in the pilot flame and tells the gas valve the flame is real. When it fails, the valve shuts the gas off as a safety measure, even though the pilot lit fine. A draft blowing out the flame or a dirty pilot orifice can cause the same thing, so a contractor will need to check which one it is.