Kansas HVAC Pros
A snow-covered two-story house illuminated by warm entrance lights during a nighttime snowfall.

Furnace Repair in Leavenworth, KS

Furnaces here run from October through April. If yours quits, tell us what it's doing and a licensed contractor who covers Leavenworth County will get in touch.

Tell us about the job

It takes about a minute.

Step 1 of 3: Equipment
An empty unfinished basement containing a forced-air furnace with overhead ductwork, exposed ceiling joists, and a single hanging light bulb.

Seven months of work in Leavenworth County cold

Your furnace runs from October through April here, seven months of the year. On winter nights that average 23°F, it cycles on and off for hours at a stretch to hold the house steady, and each start puts wear on the igniter and the flame sensor. When one of those fails, the furnace either won't light or shuts off just after it does.

Most homes here heat with gas, and a gas furnace still needs power for its blower and controls even though the flame doesn't. Leavenworth County sees winter storms and damaging wind often enough that power drops are part of the picture, and in 2024 close to a fifth of Kansas households lost power for 24 hours or more. When that happens on a cold night, the furnace stops with it and stays off until the power is back.

7 months
October through April, your furnace is on duty
23°F
the average winter night it heats against
60%
of homes here heat with gas, so most furnaces here burn gas
7 winter storms
in ten years, the nights a failure hurts most
Isometric cutaway illustration of a single-story house showing interior rooms with furniture, a furnace unit with connected ductwork and a tall vertical flue pipe extending above the dark shingled roof.
Your furnace works hardest from November through March.

NOAA nClimDiv, 1991–2020 normals

An unfinished concrete basement containing a metal HVAC air handler, exposed wooden ceiling joists with sheet-metal ducts, a hanging bare bulb, copper pipes, and stacked cardboard boxes.

A new furnace would cut about $130 a year off heating for a typical Leavenworth County home.

  • A new high-efficiency furnace$540 a year
  • An older furnace$670 a year

Estimates for a typical Leavenworth County home, compared with an older unit built to the previous federal minimum, from EIA household energy data, Kansas fuel prices and NOAA climate normals. Your home will differ.

Repair makes sense when one part has failed and the heat exchanger is sound.

Replacement makes sense when the heat exchanger is cracked or the furnace keeps needing parts.

In Kansas, HVAC licensing for homes is left to the counties and cities.

Kansas has no state license for HVAC contractors. That rule is left to counties and cities, so whether a furnace repair contractor needs a license here depends on Leavenworth County or the city the house sits in, not on any state list. There is no state record to check either way.

For a furnace repair, the gas connection is the part that matters most, since a bad one is what makes the job dangerous rather than just undone right. Whether anyone checks that connection depends on what Leavenworth County or the local city requires, since Kansas itself sets no rule on it. In Leavenworth County, 60.2% of homes heat with gas, so that connection is a real concern in this county, not a small one.

Source: Kansas Office of Revisor of Statutes

Why won't my furnace turn on?
Most often the thermostat isn't calling for heat, or the furnace isn't getting power. Check that the thermostat is set to heat and the temperature is above room temperature, and check the breaker and the furnace's own power switch, which is usually a light switch near the unit. If those are fine, the igniter or the flame sensor may have failed, and a furnace won't run without one that works. A closed gas valve will also keep it from starting, so check that it's turned to open.
Why is my furnace blowing cold air?
If air is moving but it isn't warm, the furnace may be running the blower without the burners lighting. That points to an ignition problem, a flame sensor that shut off the gas, or a limit switch that tripped from a clogged filter or blocked vent. Cold air can also mean the thermostat fan is set to on instead of auto, which runs the blower even when the burners are off between cycles. A dirty filter restricts airflow across the heat exchanger, so check that first.
Why won't my furnace pilot light stay lit?
A pilot that won't stay lit usually means the thermocouple has worn out and is no longer sensing the flame correctly, so it shuts the gas valve as a safety measure. It can also mean a draft is blowing the flame out, or the pilot orifice is partly clogged and the flame is too weak to hold. A standing pilot draws no electricity, so a power outage isn't the cause. A contractor can test the thermocouple and the gas pressure to find which one it is.