Kansas HVAC Pros
A snow-dusted white window frame with a frost-covered sill, looking out onto a snow-covered backyard during a snowstorm.

Furnace Repair in Kansas City, KS

Furnaces here run from October through April. If yours quits, tell us what it's doing and a licensed contractor who covers Wyandotte County will get in touch.

Tell us about the job

It takes about a minute.

Step 1 of 3: Equipment
An unfinished basement featuring concrete block walls, exposed floor joists, and a metal forced-air furnace with ductwork near a central pillar.

Seven months of winter nights near 23 degrees wear a furnace down

Wyandotte County homes need heat from October through April, seven months of the burner cycling on and off to hold the house against nights that average 23°F. Most homes here heat with gas, and every one of those cold starts puts wear on the igniter and the flame sensor. Eventually one of them fails, and the furnace either won't light or shuts off soon after it does.

The county has also seen 52 damaging wind events and 8 winter storms over the past ten years. Storms like that knock out power, and in 2024 close to a fifth of Kansas households lost power for a full day or more. A gas furnace still needs electricity to run its blower and controls, so when the power drops, the heat drops with it, storm or no storm.

7 months
October through April, your furnace is on duty
23°F
the average winter night it heats against
68%
of homes here heat with gas, so most furnaces here burn gas
8 winter storms
in ten years, the nights a failure hurts most
Isometric cutaway illustration of a single-story house showing interior rooms, ductwork running along the ceiling, a flue pipe through the roof, and a dark furnace unit in one corner.
Your furnace works hardest from November through March.

NOAA nClimDiv, 1991–2020 normals

A gray forced-air furnace with ductwork stands in an unfinished concrete basement surrounded by storage items and clutter.

A new furnace would cut about $130 a year off heating for a typical Wyandotte County home.

  • A new high-efficiency furnace$530 a year
  • An older furnace$660 a year

Estimates for a typical Wyandotte County home, compared with an older unit built to the previous federal minimum, from EIA household energy data, Kansas fuel prices and NOAA climate normals. Your home will differ.

Repair makes sense when one part has failed and the heat exchanger is sound.

Replacement makes sense when the heat exchanger is cracked or the furnace keeps needing parts.

In Kansas, HVAC licensing for homes is left to the counties and cities.

Wyandotte County sets its own rule for who can do this work. Kansas leaves HVAC licensing to the counties and cities instead of handling it at the state level, so whether a contractor needs a local license depends on the county the house sits in, not on any statewide test or record.

A furnace repair means gas is part of the job, and gas is the part that has to be right. Most homes in Wyandotte County heat with gas, so a loose fitting or a cracked heat exchanger is not something to leave unchecked. There is no state license standing behind that work here. Whatever authority Wyandotte County holds over gas repairs is what applies, since Kansas itself issues none.

Source: Kansas Office of Revisor of Statutes

Why won't my furnace turn on?
Most often the thermostat isn't calling for heat the way it should, or the furnace isn't getting power. Check that the thermostat is set below room temperature and has working batteries if it uses them. Look at your breaker panel too, since a tripped breaker will shut the whole unit down. If power and thermostat both check out, the igniter or a safety switch inside the furnace may be the problem, and that calls for a contractor to open it up and test it.
Why is my furnace blowing cold air?
If air is moving but it's not warm, the furnace may be running the blower without the burners lighting. A dirty filter can cause this by blocking airflow until the furnace overheats and shuts the burners off as a safety measure. It can also mean the igniter isn't lighting the gas, or the thermostat fan is set to "on" instead of "auto", which runs the blower even between heating cycles. A contractor can tell which one it is once they see the furnace running.
Why won't my furnace pilot light stay lit?
A pilot light that won't stay lit usually means the thermocouple has worn out. That's the small part that sits in the flame and tells the gas valve it's safe to stay open. When it fails, the valve reads no flame and shuts the gas off, even though the pilot was burning a second ago. A drafty vent or a dirty pilot opening can cause the same thing, so a contractor needs to check which it is before replacing anything.