HVAC Installation in Kansas City, KS
A new system here will heat from October through April and cool from May through September every year. Tell us about the house, and a licensed contractor who covers Wyandotte County will get in touch.
Tell us about the job
It takes about a minute.
What Wyandotte County asks of a new system
Your new furnace will run from October through April, seven months of the year, with winter nights averaging 23°F. On the coldest nights it has to keep working, start after start, to hold the house against that cold. Come summer, the air conditioner takes over for May through September, working through afternoons that average 87°F. Between the two, a system here is doing one job or the other almost every month of the year.
Most homes in the area heat with gas, so the furnace and the air conditioner are usually sized and installed as a pair. Wind is the storm risk to plan around here, with 52 damaging wind events recorded over the past ten years, and winter storms show up too. About one in five Kansas households lost power for a day or more in 2024, which is worth keeping in mind if you are choosing a system or backup heat that can get the house through an outage.
- 7 months
- October through April, your system heats
- 5 months
- May through September, it cools
- 23°F
- the average winter night it heats against
- 87°F
- the average summer afternoon it cools against

NOAA nClimDiv, 1991–2020 normals
In Kansas, HVAC licensing for homes is left to the counties and cities.
Wyandotte County sets its own rule for who can do this work, and Kansas keeps no state list of licensed HVAC contractors to check against. Whatever license or registration a contractor holds here comes from the county or the city, not from the state, so what it means depends on which one issued it.
For an installation like this, the permit is what stands between you and bad work. Putting in a new furnace or air conditioner means running gas or electrical connections and tying into ductwork, and in most cities and counties that calls for a permit from the local building office along with an inspection once the job is done. That inspection is what catches a bad connection or a wiring mistake before it becomes a problem, and it happens whether or not the county requires a license to do the work.
Source: Kansas Office of Revisor of Statutes
- When should I replace my HVAC system?
- Replace your furnace or air conditioner once repairs start happening every year, or once the unit is old enough that a breakdown feels like a matter of when, not if. A furnace working hard from October through April and an air conditioner covering summer afternoons near 87°F don't get a break here, so a unit near the end of its life has less time to fail quietly. If a technician tells you a repair costs a large share of what a new system would, that's usually the point to stop patching it. Winter lows averaging 23°F make a failed furnace an emergency, not an inconvenience, so don't wait for the coldest week to find out your system won't make it.
- Should I replace my furnace and air conditioner at the same time?
- If both units are old, yes, it's worth doing together. A furnace and air conditioner installed at the same time are matched to work with each other, and pairing an old unit with a new one can mean the new one never runs at its best. If your furnace still has years left and only the air conditioner failed, there's no reason to replace both. A contractor can look at the age and condition of each unit and tell you honestly whether pairing them makes sense for your house.
- What happens during an HVAC installation?
- A contractor removes the old furnace, air conditioner, or heat pump and sets the new equipment in place, then connects it to the ductwork, refrigerant lines, gas line or electrical circuit it needs to run. They check the ducts for leaks or damage, since ducts that were sized for the old system need to move the right amount of air for the new one too. Once everything is connected, they test the system, checking things like airflow, refrigerant charge, and that the thermostat is talking to the equipment correctly. In most Kansas cities and counties, this work needs a permit from the local building office and an inspection once it's done, so ask your contractor how that's handled before work starts.

