Furnace Repair in Great Bend, KS
Furnaces here run from October through April. If yours quits, tell us what it's doing and a licensed contractor who covers Barton County will get in touch.
Tell us about the job
It takes about a minute.
Seven months of nights near 21°F wear a furnace down
Your furnace works October through April here, seven months of the year. On nights that average 21°F, it can't idle. It fires, runs, shuts off, and fires again, over and over, all night long, every night that cold holds.
That cycle is hard on the igniter and the flame sensor, the two parts that have to work every single time the burner lights. Most homes in Barton County heat with gas, so when one of those parts finally gives out, the burner won't light at all. You'll notice it as a furnace that just blows cold air, or one that tries to start and quits.
- 7 months
- October through April, your furnace is on duty
- 21°F
- the average winter night it heats against
- 69%
- of homes here heat with gas, so most furnaces here burn gas
- 10 winter storms
- in ten years, the nights a failure hurts most

NOAA nClimDiv, 1991–2020 normals
A new furnace would cut about $130 a year off heating for a typical Barton County home.
Estimates for a typical Barton County home, compared with an older unit built to the previous federal minimum, from EIA household energy data, Kansas fuel prices and NOAA climate normals. Your home will differ.
Repair makes sense when one part has failed and the heat exchanger is sound.
Replacement makes sense when the heat exchanger is cracked or the furnace keeps needing parts.
In Kansas, HVAC licensing for homes is left to the counties and cities.
Kansas leaves this to Barton County, so whatever rule applies comes from the county or the city the house sits in, not from a state board. There is no state exam behind the work and no state license number to check. If Barton County or a city inside it licenses furnace contractors, that local office holds the record. If it does not, there is no license record at all.
More than two thirds of homes in Barton County heat with gas, which is why the gas connection on a furnace repair is the part that matters most. A bad connection is what makes this job dangerous, not the furnace itself. Where licensing is left to the county, whatever check exists on that gas work comes from the county or city where the house sits, not from the state.
Source: Kansas Office of Revisor of Statutes
- Why won't my furnace turn on?
- Start with the thermostat. Check that it's set to heat and the temperature is set above room temperature, and check that it has power or working batteries. If the thermostat looks fine, check the breaker for the furnace and the switch on the furnace itself, which looks like a light switch near the unit or on it. Gas furnaces also need the pilot lit or the igniter working, so if you smell gas at all, leave the house and call the gas company before doing anything else. If none of this brings it on, a contractor will need to look at the ignition system or the control board.
- Why is my furnace blowing cold air?
- Most often this means the blower is running but the burners haven't lit. Check the thermostat fan setting. If it's set to "on" instead of "auto", the blower runs constantly and will blow cold air between heating cycles, which is normal. If the fan is set to auto and you're still getting cold air, the igniter or flame sensor may have failed, or the gas supply may be interrupted. A furnace that's short cycling or won't stay lit needs a contractor to check the ignition and safety controls.
- Why won't my furnace pilot light stay lit?
- This usually points to the thermocouple, the small sensor that tells the gas valve the pilot is burning. When it wears out or sits out of position, it shuts the gas off even though the pilot lit a second ago. A draft blowing out the flame or a dirty pilot orifice can cause the same thing. Relighting it yourself follows the instructions on the furnace, but if it won't hold a flame after that, the thermocouple likely needs replacing.


