Kansas HVAC Pros
A two-story suburban house blanketed in snow at night, with one lit upstairs window and bare trees surrounding it.

Furnace Repair in Ottawa, KS

Furnaces here run from October through April. If yours quits, tell us what it's doing and a licensed contractor who covers Franklin County will get in touch.

Tell us about the job

It takes about a minute.

Step 1 of 3: Equipment
A gray forced-air furnace with sheet-metal ductwork stands in an unfinished basement with exposed wooden joists, concrete walls, and a hanging incandescent bulb.

Seven months of heat, in cold that keeps the burner working

Furnaces in Franklin County run from October through April. That is seven months of the year the burner has to light, warm the house, and shut off, over and over, on nights that average 24°F. Every one of those cycles puts wear on the igniter and the parts that control the flame.

Half the homes here heat with gas. When the igniter fails or the flame sensor gets dirty, the furnace won't stay lit and the house goes cold. Storms add another risk. Kansas saw 19% of households lose power for 24 hours or more in 2024, and a furnace without power will not run no matter what shape it is in.

7 months
October through April, your furnace is on duty
24°F
the average winter night it heats against
5 winter storms
in ten years, the nights a failure hurts most
Isometric cutaway illustration of a single-story house showing interior rooms, furniture, a dark furnace unit with a tall vertical flue pipe, and ductwork running under the pitched shingle roof.
Your furnace works hardest from November through March.

NOAA nClimDiv, 1991–2020 normals

An unfinished basement interior showing a gray furnace unit beneath a bare incandescent bulb, surrounded by exposed joists, concrete walls, cardboard boxes, and utility pipes.

A new furnace would cut about $120 a year off heating for a typical Franklin County home.

  • A new high-efficiency furnace$520 a year
  • An older furnace$640 a year

Estimates for a typical Franklin County home, compared with an older unit built to the previous federal minimum, from EIA household energy data, Kansas fuel prices and NOAA climate normals. Your home will differ.

Repair makes sense when one part has failed and the heat exchanger is sound.

Replacement makes sense when the heat exchanger is cracked or the furnace keeps needing parts.

In Kansas, HVAC licensing for homes is left to the counties and cities.

Kansas has no state license for this work. Franklin County or the city where the house sits may set its own rule, so what applies here depends on the address, not on any state record.

A furnace repair means gas, and gas is the part that has to be done right. About half the homes in Franklin County heat with gas, so a bad connection is not a rare concern here. With no state license behind the work, whatever check exists comes from the county or city, not from Topeka.

Source: Kansas Office of Revisor of Statutes

Why won't my furnace turn on?
Start with the thermostat. Check that it's set to heat and the temperature is above room temperature, and make sure it has power if it runs on batteries. If the thermostat looks fine, check the furnace switch, the one that looks like a light switch near the unit, and the breaker at your panel. A furnace that still won't start after that usually has a problem with the igniter, the flame sensor, or a safety switch, and those need a contractor to check.
Why is my furnace blowing cold air?
Most often this means the furnace hasn't started heating yet but the fan is already running, which is normal for a minute or two after a cycle starts. If cold air keeps blowing during a full cycle, the igniter or flame sensor may be failing, so the burners aren't lighting even though the blower is. A dirty filter can also cause this by starving the burners of airflow they need to run properly. With lows around 24°F this time of year, it's worth getting checked quickly rather than waiting it out.
Why won't my furnace pilot light stay lit?
This usually points to the thermocouple, the small part that senses the pilot flame and tells the gas valve it's safe to stay open. When it wears out or sits out of position, the gas valve shuts the pilot off as a safety measure. A draft blowing across the pilot can also blow it out, so check if anything nearby is causing airflow near the unit. If it keeps going out after you relight it, the thermocouple likely needs replacing.