Kansas HVAC Pros
A snow-covered two-story house at night during a blizzard, with one illuminated upstairs window.

Furnace Repair in Hays, KS

Furnaces here run from October through April. If yours quits, tell us what it's doing and a licensed contractor who covers Ellis County will get in touch.

Tell us about the job

It takes about a minute.

Step 1 of 3: Equipment
An unfinished concrete basement containing a gas furnace with sheet-metal ductwork, utility shelving, and exposed overhead joists.

Seven months of heat, and nights near 20 degrees

Furnaces in Hays run from October through April. That is seven months of the burner lighting and shutting off, night after night, on winter lows that average 20°F. Every start puts wear on the igniter and the flame sensor, and after enough winters one of them fails to do its job. The furnace tries to light, doesn't, and shuts itself down.

Most homes here heat with gas, so when a part like that goes, there's no backup warming the house while it waits on a repair. Ellis County has also logged 29 winter storms and 136 damaging wind events over the past ten years, and storms like that knock out power along with the heat. Statewide, 19% of households went at least 24 hours without power in 2024. A furnace that loses power mid-cycle needs to be checked before it's trusted to run on its own again.

7 months
October through April, your furnace is on duty
20°F
the average winter night it heats against
64%
of homes here heat with gas, so most furnaces here burn gas
29 winter storms
in ten years, the nights a failure hurts most
Isometric cutaway illustration of a single-story house showing interior rooms with furniture, ceiling ductwork, a furnace unit with a tall flue pipe, and a dark shingled roof.
Your furnace works hardest from November through March.

NOAA nClimDiv, 1991–2020 normals

An unfinished basement containing a gray HVAC furnace with ductwork, exposed wooden joists, a concrete floor, and miscellaneous clutter in one corner.

A new furnace would cut about $140 a year off heating for a typical Ellis County home.

  • A new high-efficiency furnace$550 a year
  • An older furnace$690 a year

Estimates for a typical Ellis County home, compared with an older unit built to the previous federal minimum, from EIA household energy data, Kansas fuel prices and NOAA climate normals. Your home will differ.

Repair makes sense when one part has failed and the heat exchanger is sound.

Replacement makes sense when the heat exchanger is cracked or the furnace keeps needing parts.

In Kansas, HVAC licensing for homes is left to the counties and cities.

Kansas leaves this to the county and the cities in it, so whether a furnace repair needs a local license depends on the address. Some cities license or register HVAC contractors on their own books. Others leave it open. There is no state exam behind any of it and no state record to check, because the state never entered the picture.

With 64% of homes in Ellis County heating with gas, the part of this job that matters most is the gas connection, since that is where a mistake turns dangerous. Whatever inspection that connection gets comes from the city's or county's own building or gas code, if the address has one, not from a state license. What stands behind the work here is set locally, not by Kansas.

Source: Kansas Office of Revisor of Statutes

Why won't my furnace turn on?
Most often it's the thermostat, the power supply, or the igniter. Check that the thermostat is set to heat and the batteries aren't dead. Next check the breaker and the furnace's power switch, which looks like a light switch near the unit. If those are fine, the igniter may have failed, which a contractor can test and replace.
Why is my furnace blowing cold air?
The furnace is likely running the blower without the burners lighting. That can happen if the flame sensor is dirty and shuts off gas flow, or if the pilot or igniter isn't lighting the burners at all. It can also mean the thermostat fan is set to on instead of auto, which pushes air through even when the furnace isn't heating. A contractor can check the burners and the sensor to find which one it is.
Why won't my furnace pilot light stay lit?
A pilot that won't stay lit usually points to the thermocouple, the small sensor that tells the gas valve the flame is burning. When it wears out or sits out of position, the valve shuts the gas off even though the pilot is lit. A draft blowing across the pilot or a dirty pilot orifice can also cause it. A contractor can check the thermocouple's position and replace it if it's worn.