Furnace Repair in Garden City, KS
Furnaces here run from October through April. If yours quits, tell us what it's doing and a licensed contractor who covers Finney County will get in touch.
Tell us about the job
It takes about a minute.
Seven months of Garden City winter wears on a furnace
Your furnace works from October through April here, and on the nights it works hardest, the temperature outside averages 20°F. That means long runtimes and a burner that cycles on and off for hours at a stretch. Each start puts load on the igniter, and over enough cold nights that part is often the one that fails first, leaving the burner unable to light at all.
Finney County has seen 21 winter storms in the last ten years, along with 252 damaging wind events. Storms like that knock out power, and in 2024, 19% of Kansas households lost power for a full day or more. A furnace with a standing pilot will keep running through an outage like that. Most others will not, but they come back on by themselves once the power is back, no relighting needed.
- 7 months
- October through April, your furnace is on duty
- 20°F
- the average winter night it heats against
- 73%
- of homes here heat with gas, so most furnaces here burn gas
- 21 winter storms
- in ten years, the nights a failure hurts most

NOAA nClimDiv, 1991–2020 normals
A new furnace would cut about $130 a year off heating for a typical Finney County home.
Estimates for a typical Finney County home, compared with an older unit built to the previous federal minimum, from EIA household energy data, Kansas fuel prices and NOAA climate normals. Your home will differ.
Repair makes sense when one part has failed and the heat exchanger is sound.
Replacement makes sense when the heat exchanger is cracked or the furnace keeps needing parts.
In Kansas, HVAC licensing for homes is left to the counties and cities.
Kansas leaves this to Finney County and whatever city the house sits in, so there is no state record to check either way. Whatever rule applies here comes from the county or city office, not from Topeka, and it stops at the county line.
A furnace repair means a gas connection, and that is the part that has to be right. Most homes in Finney County heat with gas, so this is the ordinary job here, not a rare one. Whether that connection gets inspected depends on what the local building office requires on this kind of repair, since there is no statewide rule filling that gap.
Source: Kansas Office of Revisor of Statutes
- Why won't my furnace turn on?
- Start with the thermostat and the power switch, since those cause more no-heat calls than the furnace itself. Check that the thermostat is set to heat and a few degrees above room temperature, and check that the switch on or near the furnace, which looks like a light switch, is on. If those are fine, the furnace may be getting no power at all, which means a tripped breaker or a blown fuse, or it could be a safety switch has shut it down because of an open door panel or a clogged filter. A furnace with a standing pilot needs that pilot lit before it will run, and a furnace with an igniter needs power to the control board. A contractor can trace which one it is.
- Why is my furnace blowing cold air?
- Most of the time this means the blower is running but the burners never lit. A furnace pushes air through the ducts whether or not that air has been heated, so a bad igniter, a dirty flame sensor, or a gas supply issue will still leave the fan running while the air stays cold. It can also mean the thermostat fan setting is on 'on' instead of 'auto', which circulates room air between heating cycles. With Finney County winters running 20°F on average and heat needed from October through April, a furnace stuck blowing cold is worth having looked at quickly. A contractor can check the ignition system and confirm what's stopping the burners from firing.
- Why won't my furnace pilot light stay lit?
- This is almost always the thermocouple, the small sensor that sits in the pilot flame and tells the gas valve it is safe to stay open. When it wears out or sits slightly out of position, it reads the flame as out even when it is lit, and the gas valve shuts off. A draft blowing across the pilot or a dirty pilot orifice can cause the same problem. This part is not something to keep relighting over and over, since a furnace that keeps failing safety checks needs a contractor to find out why.


