Furnace Repair in Dodge City, KS
Furnaces here run from October through April. If yours quits, tell us what it's doing and a licensed contractor who covers Ford County will get in touch.
Tell us about the job
It takes about a minute.
Seven months of heat, and nights that never let up
Your furnace works from October through April here, and on the coldest nights it's fighting to keep up with lows around 21°F. That means long burner cycles, night after night, for most of the year. Every time it fires, the igniter and the flame sensor take the wear. Over a few winters that adds up, and one cold morning the furnace just won't light.
Most homes in Ford County heat with gas, so when the furnace goes out, there's no backup warming the house. Wind is part of the problem too. This area has logged 251 damaging wind events over the past ten years, along with 37 winter storms, and either one can knock out power. Kansas saw 19% of households lose power for a full day or more in 2024. If your furnace has electronic ignition, no power means no heat, right when you need it most.
- 7 months
- October through April, your furnace is on duty
- 21°F
- the average winter night it heats against
- 73%
- of homes here heat with gas, so most furnaces here burn gas
- 37 winter storms
- in ten years, the nights a failure hurts most

NOAA nClimDiv, 1991–2020 normals
A new furnace would cut about $130 a year off heating for a typical Ford County home.
Estimates for a typical Ford County home, compared with an older unit built to the previous federal minimum, from EIA household energy data, Kansas fuel prices and NOAA climate normals. Your home will differ.
Repair makes sense when one part has failed and the heat exchanger is sound.
Replacement makes sense when the heat exchanger is cracked or the furnace keeps needing parts.
In Kansas, HVAC licensing for homes is left to the counties and cities.
Kansas has no state license for HVAC contractors. Whether a furnace repair contractor is licensed depends on the county or city where the house sits, so a business that meets Ford County's rules may not hold any license at all somewhere else, and there is no state board keeping a record of complaints or pulling anyone's credentials.
Most homes in Ford County, 72.5 percent, heat with gas, so a furnace repair often means someone working on a gas connection. That connection is the part of the job where a mistake matters most. In Kansas, what stands behind that work is whatever Ford County itself requires, not a state license.
Source: Kansas Office of Revisor of Statutes
- Why won't my furnace turn on?
- Most of the time it's the thermostat, the power, or the gas supply, and it pays to check the simple things first. Make sure the thermostat is set to heat and set above room temperature, and check that the furnace switch, the one that looks like a light switch near the unit, is on. Check your breaker panel too, since a tripped breaker will shut the whole system down. If all of that checks out and it still won't start, the igniter or a safety switch is likely the problem, and that calls for a contractor to test it.
- Why is my furnace blowing cold air?
- If air is moving but it's not warm, the furnace may be running on the blower alone without the burners lighting. That points to an ignition problem or a flame sensor that's failing, both things a furnace won't run on for long without shutting down. It can also mean the thermostat fan is set to "on" instead of "auto", which pushes air through the ducts even between heating cycles. Check that setting first, since it's the one thing you can rule out yourself.
- Why won't my furnace pilot light stay lit?
- This usually comes down to the thermocouple, the small part that senses the flame and tells the gas valve it's safe to stay open. When it wears out or sits dirty, it reads the flame as out even when it isn't, and shuts the gas off. A draft blowing out the pilot is another common cause, so check for airflow near the unit. Either way, a furnace with a standing pilot needs no power to keep that flame lit, so if it keeps going out, the part itself needs attention, not the electrical supply.


