Furnace Repair in Emporia, KS
Furnaces here run from October through April. If yours quits, tell us what it's doing and a licensed contractor who covers Lyon County will get in touch.
Tell us about the job
It takes about a minute.
Seven months of heat, and a grid that doesn't always hold
Your furnace works from October through April here, seven months out of the year. On winter nights that average 23°F, it runs long stretches to keep the house warm, and the burner cycles on and off again and again to hold that temperature. Each cycle puts wear on the igniter and the parts that control the flame, and over a winter that wear shows up as a furnace that will not light or one that starts and then shuts back down.
More than half the homes here heat with gas. Lyon County has had 13 winter storms and 90 damaging wind events over the past ten years, and in 2024, 19% of Kansas households went at least 24 hours without power. When the power drops on a cold night, a gas furnace with electronic ignition will not restart on its own. It needs power to light, and it needs someone to check it once that power is back.
- 7 months
- October through April, your furnace is on duty
- 23°F
- the average winter night it heats against
- 54%
- of homes here heat with gas, so most furnaces here burn gas
- 13 winter storms
- in ten years, the nights a failure hurts most

NOAA nClimDiv, 1991–2020 normals
A new furnace would cut about $120 a year off heating for a typical Lyon County home.
Estimates for a typical Lyon County home, compared with an older unit built to the previous federal minimum, from EIA household energy data, Kansas fuel prices and NOAA climate normals. Your home will differ.
Repair makes sense when one part has failed and the heat exchanger is sound.
Replacement makes sense when the heat exchanger is cracked or the furnace keeps needing parts.
In Kansas, HVAC licensing for homes is left to the counties and cities.
Lyon County sets its own rule for who can do this work, and Kansas does not step in with a state license behind it. Whether a contractor has to register, carry insurance, or meet any standard at all depends on the city or county office where the house sits, not on any state office. That means the protection a homeowner gets here is only as strong as what the local government decided to require.
For a furnace repair, the part that matters most is the gas connection, since a bad one is what makes the job dangerous rather than just broken. There is no state license to hold a contractor accountable for that connection in Kansas, so whatever check exists on this job comes from the county or city, not from a state board. More than half the homes in Lyon County heat with gas, which is what makes that connection the piece worth knowing about before the work starts.
Source: Kansas Office of Revisor of Statutes
- Why won't my furnace turn on?
- The thermostat is the first thing to check. Make sure it's set to heat and set above room temperature, and check that its batteries aren't dead. If the thermostat looks fine, check the furnace's power switch, which looks like a light switch near the unit, and check the breaker for it. A furnace that still won't respond after that has an ignition, control board, or safety switch problem that needs a contractor to diagnose.
- Why is my furnace blowing cold air?
- Air that stays cold once the furnace has been running a few minutes usually means the burners aren't lighting even though the blower is. A dirty flame sensor is a common cause, and so is a clogged filter that overheats the furnace and shuts down the burners as a safety measure. If air only feels cool at first before warming up, that's normal, since the blower starts before the burners heat the air passing over the exchanger. Check the filter first, and if it's clean and the air stays cold, a contractor needs to look at the ignition system.
- Why won't my furnace pilot light stay lit?
- This almost always means the thermocouple is worn out or out of position. The thermocouple is the small sensor that sits in the pilot flame and tells the gas valve it's safe to stay open. When it can't sense the flame properly, the gas valve closes and the pilot goes out. A draft blowing across the pilot or a dirty pilot orifice can also cause it, but a thermocouple that needs replacing is the most common reason. This is gas valve work, so it needs a licensed contractor rather than a homeowner fix.


